|
Socket Head Kit
|
Department
|
Full Description
|
|
Part Number
|
Purchase
|
|
Motor Mounts
|
Block
|
This Kit supplies the Socket Head Bolts to Attach the Motor
Mounts to the Engine.
|
|
MODSHALLMMK107
|
|
|
Starter Bolt Kit
|
Block
|
Kit mounts both 2 or 3 Bolt Starters
|
|
MODSHALLSBK109
|
|
|
Bell Housing Bolt Kit
|
Block
|
Kit allows the transmission to be mated to the engine
|
|
MODSHALLBHK106
|
|
|
Engine Stand Bolt Kit
|
Block
|
With this Kit you can easily bolt your Modular Block to most
engine test stands
|
|
MODSHALLESBK107
|
|
|
Dip-Stick Tube Bolt Kit
|
Block
|
Secures the Dip-Stick Tube to the Block
|
|
MODSHALLDST009
|
|
|
Timing Chain Guide Bolt
|
Block
|
Secures the Timing chain Guide to the block
|
|
MODSHALLTCG009
|
|
|
Timing Chain Tensioner kit
|
Block
|
Mounts the Timing Chain Tensioner to the Block
|
|
MODSHALLTCT009
|
|
|
Exhaust Manifold/Header Bolt Kit
|
Block
|
Mounts one (1) Exhasut Manifold or Header to the Block.
Two (2) needed per Engine
|
|
MODSHALLEMBK001
|
|
|
Engine Main Side Bolt Kit (Iron Block)
|
Block
|
Secures the Engine's Main Bearing Caps to the Sides
of the Block. Our Bolts are much stronger then stock parts for peace of mind
|
|
MODSHIRONSBK001
|
|
|
Engine Main SIde Bolt Kit (Aluminum Blocks)
|
Block
|
Secures the Engine's Main Bearing Caps to the Sides of the Block. Our Bolts are much stronger then stock parts for
peace of mind
|
|
Aluminator, WAP or NVH Aluminum Block
MODSHALUMMSBK001
TEKSID Aluminum Block only
MODSHTEKSID001
|
|
|
Dry Sump Pump Mounting Kit
|
Lubrication
|
Kit supplies needed parts to mount one (1) Dry Sump Pump
Mounting Plate to Engine
|
|
MODSHALLDSPM009
|
|
|
Engine Oil Pan Mounting Kit
|
Lubrication
|
Supplies all Bolts needed to mount one (1) Engine Oil Pan
to Block, both OEM and Aftermarket Pans
|
|
MODSHALLOPMK009
|
|
|
Oil Cooler/Filter Mounting Kit
|
Lubrication
|
Mounts the Engine Oil Cooler/Filter or Aftermarket oil Re-location
Plate to Engine Block
|
|
MODSHALLOCFM009
|
|
|
Oil Pump Mouinting
Kit
|
Lubrication
|
Mounts the Engine Oil Pump Inside the Block. Also comes
with hardware to mount the Pick-Up Tube to Pump
|
|
MODSHALLOPMK001
|
|
|
Camshaft Bearing Mounting Plate Kit
|
Lubrication
|
Kit mounts the Camshaft Bearing Cap Mounts to the Head.
Longer and Stronger Bolts allow a better/tighter Bearing Cap Union. Kit contents mount one head, two (2) kits needed
per Engine
|
|
MODSH4VCBMP004
|
|
|
Rear Seal Mounting Plate Kit
|
Block
|
Kit mounts the Rear Main Seal Plate to the back of the Block
|
|
MODSHALLRSMP009
|
|
|
Front Timing Cover Kit
|
Lubrication
|
This Kit mounts the Front Timing Cover to the Block
|
|
MODSH0304FTC001
|
|
|
Water Pump Mounting Kit
|
Cooling
|
Mounts One (1) Water Pump to the Block
|
|
MODSHALLWPMK001
|
|
|
Water Pump Pulley Mounting Kit
|
Cooling
|
Mounts Drive Pulley to Water Pump
|
|
MODSHALLWPPK001
|
|
|
Water Heater Tube Kit
|
Cooling
|
|
|
MODSHALLWHT004
|
|
|
Water Heater Connector Kit
|
Cooling
|
|
|
MODSHALLWHC004
|
|
|
Water Coolant Cross-Over Tube
|
Cooling
|
Secures the Water Coolant Cross-Over Tube to the Heads
|
|
MODSH9904WCT004
|
|
|
Top Alternator Brace Kit
|
Charging System
|
|
|
MODSH9904TAB004
|
|
|
Alternator Mounting Kit
|
Charging System
|
This Kit is used to attach the Alternator to its mount.
|
|
MODSH0304AMK001
|
|
| |
|
|
|
MODSHALLSBK109
|
|
|
Upper Intake Manifold to Throttle Body
|
Fuel System
|
Kit mounts the Throttle Body to Intake Manifold
|
|
MODSH9904TBIM004
|
|
|
Upper Intake Manifold Kit
|
Fuel System
|
|
|
MODSH9904UIML004
|
|
|
Lower Intake Manifold Kit
|
Fuel System
|
|
|
MODSH9904LIMH004
|
|
|
Electronic Vacuum Regulator Kit
|
Emissions
|
Kit mounts the Electronic Vacuum Regulator to the top of the Intake Manifold
|
|
MODSH9904EVR049
|
|
|
Fuel Rail Mounting Kit
|
Fuel System
|
Kit mounts the Fuel Rails to the Manifold
|
|
MODSH9904FRTM004
|
|
|
Throttle Cable Bracket Kit
|
Fuel System
|
Kit mounts Throttle Cable Bracket to the Intake manifold.
|
|
MODSH9904TCBM044
|
|
|
Idle Air Control Valve Mounting Kit
|
Fuel System
|
Kit Mounts the Idle Air Control Valve
|
|
MODSH9904IDA044
|
|
|
EGR Valve Mounting Kit
|
Emission
|
Mounts EGR Valve to back od Blower body. Looks as good
as it holds.
|
|
MODSH4VEGR001
|
|
|
Throttle Position Switch Kit
|
Fuel Management
|
Kit mounts the Throttle Position Switch to Throttle Body
|
|
MODSHALL000001
|
|
|
Fuel Transducer Bolt Kit
|
Fuel Management
|
Kit Mounts pick-up Cable to Fuel Transducer
|
|
MODSHALL000004
|
|
|
Crankshaft Position Sensor Kit
|
Ignition System
|
Mounts Crackshaft Positiion Sensor to Front Timing Cover
|
|
MODSHALLCRPS002
|
|
|
Camshaft Position Sensor Kit
|
Ignition System
|
Kit mounts the Camshaft Position Sensor to the upper Timing
Cover
|
|
MODSHALLCMPS001
|
|
|
Cylinder Head Temperature Kit
|
|
Kit mounts the Cylinder Head Temperature Sensors on the back
of each head. One kit for each sensor
|
|
MODSHALLCHT001
|
|
|
Valve Cover Bolt Kit
|
|
Valve Cover Bolt Kit, Fits all 4V Heads
|
|
MODSH0304VCK004
|
|
|
Coil Cover Bolt Kit
|
|
Coil Cover bolt kit, works on all 4V Heads, Looks great
|
|
MODSH0304CCK004
|
|
|
Belt Tensioner Mounting Kit
|
Belt Drive System
|
Kit mounts the Belt Tensioner to the Front Timing Cover.
Bolt kit looks great! try the Stainless Steel
|
|
MODSHALLBTMB001
|
|
|
Idle Pulley Bolt Kit
|
Belt Drive System
|
Kit mounts one (1) Idler pulley. Looks great and strong
too.
|
|
MODSHALLIPBK001
|
|
|
Power Steering Pump Mounting Kit
|
Belt Drive System
|
Kit mounts one Power Steering Pump to side of engine.
|
|
MODSHALLPSBK001
|
|
|
AC Compressor Mounting Kit
|
Belt Drive System
|
Kit mounts one AC Compressor to your engine
|
|
MODSHALLACM001
|
|
| |
|
|
|
|
|
|
Thermostat Housing Bolt Kit
|
Cooling System
|
Kit replaces the bolts that hold the thermostat together
|
|
MODSH0304THK004
|
|
|
Valve
Cover Kits
Threaded Stud
|
|
Valve Cover Kit
We use only the best Threaded Studs we can fine, then combined that with the same Super Hard and Durable Washers we use in
our Socket Head Kits, and throw in the right amount of Flanged Nuts. This combo makes for a very strong and formidable
fastener kit. Studs should always be used when available and when the conditions allow. This kit allows the installation of one Valve Cover.
|
|
|
Front Engine
(Timing) Cover
Threaded Stud
|
|
Front Engine (Timing)
Cover
There isn't a better Threaded Stud Kit on the market, and Pro
Weld has them. This kit mounts the Front Engine (Timing) Cover to the engine. Threaded
Studs save wear and tear on threaded holes, especially when used in aluminum engine blocks. We used only
the finest pieces in our kits, and this one is no different. Kit does one
complete front engine cover
|
|
|
Water Pump Kit
Threaded Stud
|
|
Water Pump Kit
This kit mounts the Water Pump Securely to the front of the engine block.
We only use the best Threaded Studs, Washers and Flanged Nuts Available.
Kit mounts one Water Pump
|
|
|
Water Pump Pulley, Drive Hub,
Stud Mounting Kit
Stud Kit
|
|
Water Pump
Pulley, Drive Hub, Stud Mounting Kit
We use this kit to mount the
Drive Hub/Pulley to the Water Pump. You can combine this kit with the Water Pump Mounting Kit, to make a bullet proof
Water Pump Assembly.
|
|
|
Oil Pan Stud Kit
Threaded
Stud
|
|
Oil Pan Stud Kit
Our Oil Pan Threaded Stud Kit is just the ticket
for Racer. The Threaded Stud Kit allows multiple Oil Pan removals to inspect the lower end, without fear of wear on
the threaded holes in the engine. But, you also don't have to be a racer to figure out the benefit of using this
stud kit, and as always, we used only the beast pieces for this kit.
Kit mounts one stock or aftermarket oil pan
|
|
|
Bell Housing Stud Kit
Threaded Stud
|
|
Bell
Housing Stud Kit
Wow, Tires of lying on your back trying to alien
the Engine to the Transmission? So is everyone else. Besides helping to protect the threads from wear and the
very real chance of cross-threading, our Bell Housing Threaded Stud kit is a life saver, and possibly a engine block saver
as well.
Kit contains everything for one engine
|
|
|
Rear Main Seal Plate Kit
Threaded Stud
|
|
Rear Main Seal Plate
Don't take a chance with your engine, use our Threaded Stud kit on all your
engines available threaded holes, and protect against striped threads, worn threads or cross-threads. This kit mounts
the Rear main Seal Plate to the rear most section of the Engine Block.
Kit mounts one Rear Seal Plate
|
|
|
Exhaust Manifold/Header Stud Kit
Threaded Stud
|
|
Exhaust Manifold/Header Stud Kit
Our Threaded Stud kits can dramatically increase
the speed and ease of installing Headers and Exhaust manifolds, when available. Because of the harsh nature of the exhaust
manifold, the threaded holes that hold these Headers on can get severely damaged or striped by repeated use. Use our
Studs and save your Heads.
One Kit mounts one Header or Exhaust manifold
|
|
|
Engine Oil Cooler/Filter,
Stud Kit
Threaded Stud Kit
|
|
Engine Oil Cooler/Filter Mount
Our oil Cooler/Filter assembly Mounting Kit uses the very best Threaded Studs
we can fine. This Stud Kit also works with all aftermarket Remote Filter mounts from Moroso, Canton and even our own
Dry Sump plate from Aviaid. When only the best will do, Call Pro Weld.
Mounts One Cooler/Filter Assembly
|
|
| |
|
|
|
